Grouts & Anchors Systems

KingGrout PG300^®

High strength pourable epoxy resin grout.

⬇ Download TDS Request a Quote →

Mixed density

2.00 ± 0.1 g/cm³

D2471

min @ 55oC

Water absorption

ASTM: ≤ 0.15% C413

Flow (using 200 ml cone)

200 ± 10 mm

Packaging

Pack

Standards

4 cited

ASTM 35 · ASTM D2369

Overview

KingGrout PG300 is a three component, high strength, and free flowing epoxy resin grout. KingGrout PG300 is suitable for grouting large gaps from 10 to 400 mm at high ambient temperatures of up to 55°C.

Applications

KingGrout PG300 is ideally designed for use in the following applications:
Machine base plates
Heavy crane rails
Bearing plinths
Anchoring of steel fixings
High speed turbines
Grouting areas where occasional chemical spillage may occur

Advantages

Resistant to dynamic loading
Non-shrink and low creep characteristics under continuous loading
Exceptional high compressive, flexural and tensile strengths
Extremely dense
Exceptional bond to concrete and steel surfaces
Good chemical resistance
High ultimate and early strengths

Technical Properties

Property	Value	Standard
Mixed density	2.00 ± 0.1 g/cm³	—
Working life	80 ± 10 min @ 25oC 40 ± 10 min @ 40oC	—
Compressive strength	ASTM ≥ 50 MPa @ 25oC ≥ 75 C579 @ 1 day @ 3 days @ 7 MPa @ 40oC ≥ 70 MPa @	—
days	25oC ≥ 85 MPa @ 40oC ≥ 85 MPa @ 25oC ≥ 95 MPa @ 40oC	—
Flexural strength	EN: ≥ 35 MPa @ 40oC 13892-2 @ 7 days	—
Tensile strength	≥ 15 MPa @ 40oC @ 7 days	BS 6319-7
Recommended working	15 - 55oC ambient temperature Crack formation temperature No cracks or bleeding	—
@ 400 mm		—
Peak exothermic	55 ± 2oC @40oC 66 ± 2oC	—
temperature	@ 55oC	ASTM D2471
Peak exothermic time	± 5 min @ 40oC 25 ± 5	ASTM 35
D2471	min @ 55oC	—
Water absorption	ASTM: ≤ 0.15% C413	—
Flow (using 200 ml cone)	200 ± 10 mm	—
VOC	: < 10 g/ltr (complies with LEED) Care should be taken to ensure that the bottom and the product sides are thoroughly scraped and used. Mix the two components for 2 minutes. The filler should be gradually added while mixing. Mixing should continue for 3 minutes or until a uniform consistency obtained. THICKNESSES AND SIZE LIMITATIONS Flo-Grout EP 340 is suitable for grouting large gaps from 10 to 400 mm. For greater thicknesses, multiple layers can be applied after initial curing of the previous layer. PLACING AND FINISHING	ASTM D2369
Under Base plate	Enough material should be available to achieve a continuous fill and to complete the work. Pouring of the mixed grout should be started from one side only to avoid air entrapment. To obtain maximum flow distance, a side shutter feed with 100 mm side height should be erected and used to build the required head. At 100 mm of head, a flow distance of 2100 mm can be achieved at gap thicknesses of 100 mm @ 25°C ambient temperatures.	—
Formwork	KingGrout® PG300 High strength pourable epoxy resin grout. As the mixed grout possesses high fluid characteristics, all formwork and shutters should be water tight. This can be achieved by sealing underneath the formwork and at the joints by using an appropriate mastic.	—